Behind the build

How Cubicles Are Remanufactured, Step by Step

What actually happens between a corporate floor coming out and a remanufactured or hybrid workstation going in.

8 minute read  ·  Updated November 2026
6x6 remanufactured hybrid workstation with glass stacker panels, black trim, white corner worksurface and box-box-file pedestal

"Remanufactured" can sound like a marketing word, but it describes a specific process. Done properly, it takes a used panel system apart, keeps the parts that are built to last, and replaces the parts that show their age. This guide walks through each step, explains where a hybrid workstation fits, and lists the questions that separate a real rebuild from a quick clean.

Step 1: Sourcing

Every remanufactured station starts on someone else's floor. When a company closes an office, downsizes or relocates, its panel system is removed, often as part of an office furniture liquidation or decommissioning. Systems that come out in quantity, from established manufacturers and in common configurations, are the most valuable for remanufacturing, because parts are interchangeable and easy to match.

Good sourcing matters more than any later step. A large run of one system gives consistent panels, matching hardware and enough spares to replace anything that fails inspection.

Step 2: Teardown and sorting

Stations are taken apart into their components: panels, connector posts, worksurfaces, brackets, pedestals, trim and power parts. Each type is sorted by size and height. Panels are grouped by width and height so a project can be built from matching stock.

This is also when worn-out consumables come off for good. Old fabric, chipped trim and damaged worksurface edges are removed and set aside for recycling or disposal.

Step 3: Inspection

Every panel core is checked before it goes any further. Inspectors look for bent or cracked frames, damaged connection points, and anything that would stop a panel from carrying a loaded worksurface safely. Hardware such as brackets and connectors is checked for wear and straightness. Power components are tested or replaced.

Parts that fail inspection do not go back into a station. The ability to reject parts is why sourcing large runs matters: there is enough good stock to build a full floor without compromise.

Step 4: Re-covering panels

This is the step that changes how a floor looks. Each sound panel core is cleaned and fitted with new fabric, stretched and secured so the surface is smooth and tight. Fabric choice depends on the grade:

  • Hybrid: new fabric from in-stock colors, which keeps the schedule short.
  • Remanufactured: new fabric from a wider range, chosen to match your brand or design.

Some panels are finished in other materials, such as laminate or painted metal on the lower section, or glass stackers at the top. These are specified per project. See the glass stacker guide.

Step 5: Worksurfaces, trim and hardware

Worksurfaces take the most daily wear, so rebuilt stations get new laminate tops, cut to the station's layout with clean edges. L-shaped stations are built from separate pieces, a corner and returns, which keeps them easy to move later.

Trim and caps, the finish pieces on the tops and ends of panels, are replaced with new ones so the frames read as new. Steel hardware is cleaned, checked and refinished. Pedestals are cleaned and checked, with locks, slides and pulls replaced where needed, or supplied new.

Step 6: Kitting and installation

Once a layout is approved, parts for each station are kitted together, labeled and staged for delivery. Installers then build the stations on site to the scaled plan: panels and connectors first, then worksurfaces, storage and power. Electrical hookup to the building is handled by a licensed electrician where required.

From an approved layout, remanufactured workstations usually take 7 to 14 days to build. Hybrid workstations are delivered and installed in about 2 weeks in most cases. The two-week installation guide shows a realistic schedule.

Where hybrid fits

A hybrid workstation follows the same process with a defined scope: recycled office panel cores + new trim, refinished hardware, new worksurfaces and new in-stock fabric. Keeping the fabric to in-stock colors and reusing sound cores is what lets a hybrid come in at often around half the price of comparable new while looking as new on your floor.

StepHybridFull remanufacture
Panel coresRecycled, inspectedReused, rebuilt as needed
FabricNew, in-stock colorsNew, wider choice
WorksurfacesNewNew
TrimNewNew or refinished
HardwareRefinishedRefinished or new
TimingAbout 2 weeks installed, most casesUsually 7 to 14 days to build

Remanufacturing the cubicles you already own

The same process can be applied to your own furniture. If your office has a sound panel system that simply looks its age, it can often be refreshed instead of replaced:

  • Re-covering in place or off site. Panels get new fabric, either on site in phases or taken away and returned.
  • New worksurfaces. Replacing chipped and worn tops changes the look of a floor quickly.
  • New trim and refinished hardware. The same finishing steps as a hybrid station.
  • Reconfiguration. Changing station sizes, panel heights or the layout for a new headcount, using your parts plus added components.
  • Matching additions. Rebuilt stations from the same system family to extend your floor.

Whether to refresh or replace depends on the system, its condition and how much the layout needs to change. A free walkthrough is the quickest way to find out. If replacing makes more sense, the old system can be cleared as part of the same project.

Why it matters for waste and sustainability

Office furniture is bulky, and a single floor of cubicles fills several trucks. When a system is thrown away, the heaviest components, the panel cores and steel hardware, go with it. Remanufacturing keeps those parts in service for another lease, and only the surface materials are replaced.

The U.S. Environmental Protection Agency's figures on furniture show how much of it ends up landfilled; our office furniture landfill statistics page summarizes them. Choosing remanufactured or hybrid stations is one of the simplest ways to cut that number on your project. If your company reports on sustainability, ask how reused content and diverted material are documented for your floor.

Questions to ask

Because the words are used loosely, ask any supplier to put the scope in writing:

  1. Is the fabric new, or cleaned?
  2. Are the worksurfaces new, or the originals?
  3. Is the trim new? Is the hardware refinished?
  4. How are panel cores inspected, and what happens to ones that fail?
  5. What warranty, if any, comes with the stations?
  6. Are delivery, installation and electrical separate lines on the quote?

The used vs remanufactured vs new guide covers how each grade compares overall, and used and remanufactured cubicles shows what we install.

To price a remanufactured or hybrid floor, send your layout or headcount to hello@officestation.com or use the quote request form. Space planning is free, and every project is quoted individually.

Frequently asked questions

What does remanufactured mean for cubicles?

Remanufactured cubicles are reused panel systems that have been taken apart, inspected and rebuilt before sale. Panels are re-covered in new fabric, worksurfaces are replaced with new laminate tops, hardware is cleaned and refinished, and trim is replaced. The finished stations look and work close to new, in the finishes and sizes you choose.

What is a panel core?

The panel core is the structural part of a cubicle panel: the frame and the substrate the fabric is stretched over. It carries the worksurfaces, storage and power. Cores are built to outlast several office leases, so in a remanufactured or hybrid station they are inspected and reused, while the fabric and finishes are new.

How long does it take to remanufacture cubicles?

Remanufactured workstations usually take 7 to 14 days from an approved layout and finish selection, depending on quantity and finishes. Hybrid workstations, which use in-stock fabrics, are delivered and installed in about 2 weeks in most cases. Special-order fabrics or very large floors can take longer.

What happens to parts that fail inspection?

Cores, hardware or components that do not pass inspection are not reused in a station. Steel and other recyclable material goes to recycling where facilities exist, and the station is completed with sound parts. Ask your supplier to describe their inspection and what happens to rejected parts.

Is remanufactured furniture covered by a warranty?

Original manufacturer warranties generally do not transfer to pre-owned or remanufactured furniture, because the product has left the manufacturer's sales channel. What is covered, and for how long, depends on the seller. Ask for any warranty terms in writing with your quote.

Can my existing cubicles be remanufactured?

Often, yes. If your frames are sound and the system is a common one, your own panels can be re-covered, given new worksurfaces and reconfigured, sometimes in place. Office Station can look at the system during a free walkthrough and quote refreshing what you own against replacing it.

6x6 remanufactured hybrid workstations with 67-inch fabric panels, glass stackers, black trim and white L-shaped worksurfaces in a Phoenix office
New: hybrid workstations

6×6 Remanufactured Hybrid Workstations

Recycled office panel cores + new trim, refinished hardware, new worksurfaces and new in-stock fabric. An as-new workstation built on a proven panel system, without paying for an all-new one.

  • Often around half the price of comparable newThe panel cores are reused, so you pay for new finishes, not a whole new system.
  • Delivered and installed in about 2 weeksIn most cases, from an approved layout and fabric choice.
  • Other configurations available5×5, 6×8, 8×8, call center, benching and private offices, at 47″, 53″ or 67″.

See hybrid workstations Request a quote

Rows of office seating
Start here

Ready to furnish the space?

Pre-owned designer furniture, quoted to your project, with in-stock liquidation grade installed in as little as 72 hours.